Carbide Inserts, Carbide Endmills, Gear Hob Cutters Manufacturers China.

Understanding High Performance Carbide End Mills.

Solid Carbide End Mills Manufacturers

Cost per part, not cost per tool will help solidify a manufacturer’s bottom line.

Rising commodity prices affect every facet of our lives; you only have to look at the price of incoming raw materials and fuel to see this is the case.

One of the commodities most affecting tooling suppliers, and the products they manufacture, is tungsten carbide. Over the past decade, tungsten carbide prices have risen sharply. In 2004 alone the price rose 500 percent. According to the Tungsten Investing News, however, the price is not only high when compared to a decade ago, it also has a tendency to fluctuate rapidly.

This can make it difficult for suppliers to guarantee prices.

China, which controls nearly all of the global tungsten trade (roughly 80 percent), has been holding a tight rein on its supply recently to keep the price of this rare-earth metal trending upward. These rising tungsten prices have made tool recycling more attractive and, in some cases, changed purchasing patterns.

But has the rising cost of carbide actually affected the use of solid-carbide tooling?

According to Walter USA Product Manager Pat Nehls, productivity, not price, should drive purchasing decisions. New coatings and high-performance tool designs are two examples of productivity-boosting technologies that can have a dramatic effect on performance.

“When the customer shows high performance increases, the cost of the carbide becomes less important,” said Nehls. “Ultimately, we are selling cost per feature. When a more expensive tool produces features at a lower cost, the customer is satisfied.”

Many years ago HSS and brazed-carbide cutting tools were very popular. Today fewer and fewer shops make use of them, with solid-carbide and indexable tooling being the norm. One of the reasons for their waning use is that when a tool is at the end of its life-span, it is taken out of the machine and reground.

Reground tools have a shorter life, and predictability becomes much more difficult. A tooling “float” also must be created to ensure that tools are on hand when needed.

The use of indexable inserts, in particular, has eliminated the need for this procedure.

Cost per feature is normally lower with indexable inserts because they have two or more usable cutting edges. Photo courtesy of Walter USA.

While indexable inserts are certainly the tools of choice in many applications, shops aren’t necessarily choosing them over solid-carbide tools.

“Each tool type has its own features and benefits,” said Nehls. “For example, solid drills will typically produce holes to tighter tolerances, perhaps eliminating the need for secondary operations. This makes the solid tool the more economical choice anyway.”

Solid drills also are available in smaller increments between sizes.

On the other hand, Nehls said that indexable drills have a tighter diameter tolerance band because of their assembled nature. Cycle time may be increased, but the cost per hole is generally lower. Ultimately, the requirements of each project guide tool choice.

Conserving Carbide

“Today when an insert becomes dull, we simply index the insert and can expect relatively good repeatability and consistency,” explained John Mitchell, general manager of Tungaloy America. “Insert pressing and coating technologies advanced to where there are now major improvements in performance and chip formation. Few machine shops would want to go back to the days of HSS and brazed cutting tools. However, many shops continue to use solid-carbide tools.”

The premise is the same: Use the tools, take them out of the machine, regrind them, reset the tool, and adjust the offsets. A reground solid-carbide tool will last 80 percent as long as a new tool. In most solid-carbide end mill applications, for example, the end mill takes a conservative depth of cut (0.100 in.), yet the tool may be 3, 4, or more inches long.

“That’s a lot of carbide … nearly the entire end mill is made of carbide. This is inefficient given the rising cost of carbide and the fact that only 3 or 4 percent of this tool is actually in cut,” said Mitchell. “The same evolution that happened with HSS and brazed tools is occurring rapidly now.”

New technology has enabled some cutting tool manufacturers to produce indexable end mills, which essentially are small end mills threaded into a shank.

“Obviously, since the indexable carbide portion is only a fraction of the size of a solid-carbide tool, the cost to produce this indexable end mill can be much lower,” explained Mitchell. “The true benefits of this technology are not in the cost, but rather in its performance.”

Because the end mill is screwed into a shank, the shank can be made of different materials to produce different results. For example, for a roughing operation, it is best to use a steel or other heavy metal shank.

According to Mitchell, these shanks offer a dampening effect, which improves roughing performance by enabling a heavier cut to be made. When finishing or an extended reach is needed, it is best to use a carbide shank.

Reducing Setup Time

“Solid-carbide end mills perform at their best when held in a shrink-fit holder, but removing a used solid-carbide tool from a shrink-fit adapter can be cumbersome and time-consuming,” said Mitchell. “An indexable end mill is simple to index; in fact, most indexes can be performed right on the machine in seconds.”

After indexing the tool, an offset is not always required because the repeatability of these tools is very accurate. Setups are easier with this type of tool as well, because the location of the tool is predictable.

Even when a collet is used, the tool changes are time-consuming and labor-intensive.

First, the end mill needs to be removed, reground, and placed back into the collet holder. Then the tool must be set up using a height gauge or tool presetter, before being placed back in the machine. Following this, a trial cut is typically performed and offsets calculated and entered into the control, before the tool can run.

An indexable end mill can be switched out directly on the machine.

Recycling Carbide

The days of throwing worn tools away are over. Because only a small amount of the carbide is actually worn away during machining, inserts and solid tools should be kept as scrap and recycled.

And, in an effort to control production costs, many tooling manufacturers now offer carbide recycling programs to reduce their dependence on new carbide purchases.

“Over the last 20 years, we have seen a significant increase in recycling all scrap materials, including carbide,” said Nehls. “Customers are savvier with respect to their total production environment, and there is a lot of money in used carbide.”

Related Items

  • Product Categories

  • Contact Us

    Tel: +86 20-6109-8842

    Fax:+86 20-6282-4610

    Sales Manager:

    Email: Sam.Wu@cantontools.com

    Skype: My status
    ______________________________

    Sales Officer:

    Email: Candy.tang@cantontools.com

    Skype: My status
    ______________________________

    Sales:

    Email: Sophia@CantonTools.com

    Skype: My status
    ______________________________ ______________________________

    Office Hours: 9am - 6pm, Mon to Fri, Except for Statutory Holidays.

  •